Send Message
Home ProductsIEC Test Equipment

IEC 60745-2-5 IEC Test Equipment For Guarding Below The Guide Plate

IEC 60745-2-5 IEC Test Equipment For Guarding Below The Guide Plate

  • IEC 60745-2-5 IEC Test Equipment For Guarding Below The Guide Plate
  • IEC 60745-2-5 IEC Test Equipment For Guarding Below The Guide Plate
  • IEC 60745-2-5 IEC Test Equipment For Guarding Below The Guide Plate
IEC 60745-2-5 IEC Test Equipment For Guarding Below The Guide Plate
Product Details:
Place of Origin: China
Brand Name: HongCe
Certification: Third party calibration certificate(cost additional)
Model Number: HDD8302
Payment & Shipping Terms:
Minimum Order Quantity: 1 set
Price: Negotiatable
Packaging Details: Plywood
Delivery Time: 30 days
Payment Terms: T/T
Supply Ability: 5 set per month
Contact Now
Detailed Product Description
Product Name: Circular Saw Lower Guard Test Device Warranty: 1 Year
Power: 220V 50Hz Test Sample: Guarding Below The Guide Plate
Standard: IEC/EN 60745-2-5, IEC 62841-2-5 Test Item: Closing Time Of The Lower Guard
Automatic / Manual Speed: 0-30 Times / Min Working Station: 1
High Light:

Guide Plate IEC Test Equipment

,

Guarding Below IEC Test Equipment

,

220V IEC Test Apparatus

IEC 60745-2-5 Circular Saw Lower Guard Test Device, 0-30 times / min

 

IEC 60745-2-5 clause 19.102.3 For saws having a blade with a diameter less than 210 mm, the closing time of the lower guard from the fully open position to the fully closed position shall not exceed 0,2 s. For saws having a blade diameter 210 mm and above, the closing time of the lower guard from the fully open position to the fully closed position in seconds, shall be less than the numerical equivalent of the largest recommended blade diameter, expressed in metres, but not more than 0,3 s. During measurement, the saw is set to cut at a right angle and for maximum cutting depth, with the guide plate in the horizontal position and the saw not inverted.
Compliance is checked by measurements.

 

Standard: IEC 60745-2-5 : Particular requirements for circular saws, clause 19.102.3 and Annex BB, EN 60745-2-5, IEC 62841-2-5 clause 17.101

Application: This device is applicable to test the closing time and mechanical strength of lower guard for circular saws.

Test sample: Circular saws                   IEC Test Equipment

Feature: The saw is to be set for a 90°cut and oriented in the horizontal plane. The lower guard is to be cycled from the full closed position to the maximum open working position and then released for 50000 cycles at a rate not less than 10 cycles per minute. The cycle numbers recorded by a position sensor. Following the cycle, the closure time shall not exceed 0.3s. The device record the times when detected closure time exceed 0.3s. When preset test times completed, device record the last closure time and stop automatically.

Parameters:                                                                                                   IEC Test Equipment

No. Item Specification Remark
1 Power supply 220V/50Hz  
2 Electrical control

MITSUBISHI PLC operation,

7 Inch Touch screen operation

     IEC Test Equipment
3 Drive Motor  
4 Test times 0-999999 times, preset  
5 Detection time 0-9.99s, display Closure time
6 Automatic / manual speed 0-30 times / min, can be preset  
7 Manual state rotation

Touch control,

clockwise or counter clockwise

 
8 Dimension 80*70*100cm, about 80kg  
 

 

Picture for reference:

 

 

IEC 60745-2-5 IEC Test Equipment For Guarding Below The Guide Plate 0

Contact Details
Guangzhou HongCe Equipment Co., Ltd.

Contact Person: Tessa Huang

Tel: +8618933919125

Fax: 86-020-31143909-805

Send your inquiry directly to us (0 / 3000)

Best Products
Other Products