Send Message
Home ProductsLight Testing Equipment

Appearance Change Of Lanterns Light Testing Equipment Adjusting Devices IEC60598-1 R500mm

Appearance Change Of Lanterns Light Testing Equipment Adjusting Devices IEC60598-1 R500mm

  • Appearance Change Of Lanterns  Light Testing Equipment Adjusting Devices IEC60598-1 R500mm
  • Appearance Change Of Lanterns  Light Testing Equipment Adjusting Devices IEC60598-1 R500mm
  • Appearance Change Of Lanterns  Light Testing Equipment Adjusting Devices IEC60598-1 R500mm
  • Appearance Change Of Lanterns  Light Testing Equipment Adjusting Devices IEC60598-1 R500mm
Appearance Change Of Lanterns  Light Testing Equipment Adjusting Devices IEC60598-1 R500mm
Product Details:
Place of Origin: China
Brand Name: HongCe
Certification: calibration certificate (cost additional)
Model Number: ADL-1
Payment & Shipping Terms:
Minimum Order Quantity: 1 set
Price: Negotiatable
Packaging Details: Plywood
Delivery Time: 15 days
Payment Terms: T/T
Supply Ability: 25 set per month
Contact Now
Detailed Product Description
Mode: ADL-1 Control: PLC
Operation: Touch Screen Operation Language: English
Standard: IEC60598 Clause: IEC60598.4.14.3
High Light:

light testing equipment

,

led light tester

Appearance Change Of Lanterns Light Testing Equipment Adjusting Devices IEC60598-1 R500mm

Product information:

The device is used to detect adjustment device, and confirm to the IEC60598-1 clause 4.14.3.
The adjustment device, equipped with the appropriate cable or cord shall be operated in accordance with following table. A cycle of operation is a movement from one extreme of the range to the other and back to the starting position. The rate of movement shall not cause the device to heat appreciably and shall not exceed 600 cycles per hour. 
For adjusting devices that consist of a flexible tube, the range of adjustment for this test is normally 135° in both directions from the vertical. However, where this adjustment cannot be achieved without using unreasonable force, the flexible tube is bent only to the positions where it will remain by itself.   

 

Technical parameters:

1. The test rate can be set, set ranging from 0.1 to 10 times / min.

2. The bending angle can be set , the swing range of vertical lines on both sides of

0-180°.

3. Rotation center height: 1200mm.

4. The maximum radius of gyration of the pendulum: R500mm.

5. Maximum stroke of stretching action: 0-650mm.

6. Action angle of rotation: 0-360°.

7. Test cycles can be set, the number of cycles range 1-999999.

8. The fixtures can meet a variety of samples within the standard range of testing needs.

9. Drive motor: Servo motor.

10. Controller: Mitsubishi PLC.

11. HMI: touch screen interface.

12. Guided whole English interface, easy to operate.

13. Load: with terminals, Externally connected to load (The load is optional,cost additional ).

 

Standard Information :

 

Appearance Change Of Lanterns  Light Testing Equipment Adjusting Devices IEC60598-1 R500mm 0

Appearance Change Of Lanterns  Light Testing Equipment Adjusting Devices IEC60598-1 R500mm 1

4.11.6 Electro-mechanical contact systems shall withstand the electrical stresses occurring in normal use.

Compliance is checked by subjecting the electro-mechanical contact systems to 100 operations at a speed which corresponds to practical usage (an operation is either making or breaking the

contact). The test is made with a.c. at rated voltage, and the test current shall be 1,25 times the rated current of the electrical contact system. The power factor of the load shall be approximately 0,6, unless a different rated current is marked for resistive loads, in which case the load power factor shall be unity.

Where a luminaire is marked for both resistive and inductive loads, it shall be subjected to tests at power factors of both unity and 0,6.

Before and after the tests, the electro-mechanical contact systems shall be loaded with 1,5 times rated current, and the voltage drop across each contact shall not exceed 50 mV.

Following completion of these tests, the electro-mechanical contact system shall withstand an electric strength test made in accordance with 10.2.

After the test, the samples shall show:

– no wear impairing their further use;

– no deterioration of enclosures or barriers;

– no loosening of electrical or mechanical connections.

For electro-mechanical contact systems, the mechanical test of 4.14.3 is carried out simultaneously with this electrical test.

 

Test on adjusting devices:   

Type of luminaire

Number of cycles of operation

Luminaires intended to be frequently adjusted, 
for example drawing board luminaires

1500

Luminaires intended to be occasionally adjusted, for example shop-window spotlights

150

Luminaires intended to be adjusted during installation only, for example floodlighting luminaires

45

 

Appearance Change Of Lanterns  Light Testing Equipment Adjusting Devices IEC60598-1 R500mm 2Appearance Change Of Lanterns  Light Testing Equipment Adjusting Devices IEC60598-1 R500mm 3

Contact Details
Guangzhou HongCe Equipment Co., Ltd.

Contact Person: Tessa Huang

Tel: +8618933919125

Fax: 86-020-31143909-805

Send your inquiry directly to us (0 / 3000)

Best Products